Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1892 | Manualshive

Страница: 1892 / 2244

background image

1. Disassemble in the order indicated in

Fig. 6

.

2. Assemble in the reverse order of disassembly.

DRIVER'S SEAT

Fig. 6: Identifying Driver's Seat Components (With Torque Specifications)

Courtesy of MAZDA MOTORS CORP.

PASSENGER'S SEAT



Replacement with new passenger-side seat parts



Disassembly of the passenger-side seat



If any of the following work is performed, perform the seat weight
sensor inspection using the WDS or equivalent. (See SEAT WEIGHT
SENSOR INSPECTION .)



Removal of the passenger-side seat



Loosening and retightening of passenger's seat fixing bolts

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Seats - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:26:44 PM

Page 6

© 2005 Mitchell Repair Information Company, LLC.

«
...
1890
1891
1892
1893
1894
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: Daihatsu Страницы: 340

Бренд: B-Speech Страницы: 18

Бренд: Dacia Страницы: 238

Бренд: Metra Electronics Страницы: 8

Бренд: OHIOSTEEL Страницы: 2

CHALLENGER GK-6125A 2018

Бренд: Coolster Страницы: 45

Бренд: Husky Страницы: 8

Halo Pole Mount

Бренд: Charge Amps Страницы: 14

Бренд: EUFAB Страницы: 12

Бренд: Whispbar Страницы: 15

ENDURASHINE 63-0299

Бренд: Edelbrock Страницы: 1

2004 LAND CRUISER 100

Бренд: Toyota Страницы: 576

Бренд: Hyundai Страницы: 106

Бренд: Improved Racing Страницы: 11

Бренд: Thule Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды