Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1606 | Manualshive

Страница: 1606 / 2244

background image

5



Registration keys
(two or more)



M-MDS

lock, the engine
cannot be started.
Before beginning the
procedure, verify that
the customer has
turned in all of the
keys for the vehicle.



Unless two or more
keys are registered
after replacement, the
engine cannot be
started.



The keys (two or
more keys) readied
before beginning the
procedure do not have
to be new keys. Any
key that is capable of
starting the engine
before beginning the
procedure can be
used.

-

Replacing the coil antenna.



New coil antenna



It is not necessary to
reset the immobilizer
system.

CAUTION:



If any of the following items are touching or near the key head, signal
communication between the key and vehicle is negatively affected,
resulting in the engine not starting or the key registration failure. Do
not perform the procedure if any of the following items are touching
or near the key head.



Any metallic object



Spare keys or keys for other vehicles equipped with an
immobilizer system



Any electronic device, or any credit or other cards with
magnetic strips

NOTE:



Within the following procedures, the term a "valid key" means a "key that
can start the engine".



After adding/registering keys, clearing ID numbers or replacing any
component part of the immobilizer system, verify that all keys can start the
engine within 5 s .



When verifying that the keys can start the engine, wait at least 5 s or more

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Keyless Entry System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:35:24 PM

Page 7

© 2005 Mitchell Repair Information Company, LLC.

«
...
1604
1605
1606
1607
1608
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: JETBAG Страницы: 44

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Federal Signal Corporation Страницы: 8

Бренд: Mercedes-Benz Страницы: 30

Бренд: CITROËN Страницы: 301

RGBW Rock Lights

Бренд: Lit Lightz Страницы: 3

BEDXTENDER HD MAX 74841-00A

Бренд: AMP Research Страницы: 9

Бренд: Belkin Страницы: 2

Бренд: Power Acoustik Страницы: 4

Бренд: INDIWORK Страницы: 18

Бренд: Opel Страницы: 103

Бренд: Saab Страницы: 9

Бренд: Toyota Страницы: 779

spectroFlex Car Adapter

Бренд: wtw Страницы: 4

Бренд: Westin Страницы: 3

Бренд: Mazda Страницы: 7

Бренд: Airstream Страницы: 103

Бренд: Volkswagen Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды