Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1803

Страница: 1803 / 2244

TYPE A

1. Verify the continuity between the relay terminals.



If not as indicated in

Fig. 14

, replace the relay.

Fig. 14: Type A Continuity Table

Courtesy of MAZDA MOTORS CORP.



Cooling fan relay No.1



Cooling fan relay No.2



Cooling fan relay No.3



Trunk lid opener relay

Type B



Headlight relay



Ignition relay

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Power Systems - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:28:36 PM

Page 13

«
...
1801
1802
1803
1804
1805
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды