Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 239

Страница: 239 / 2244

Fig. 12: View Of Passenger-Side Air Bag Module & Components (With Torque Specifications)
Courtesy of MAZDA MOTORS CORP.

6. Install in the reverse order of removal.

7. Turn the ignition switch to the ON position.

8. Verify that the air bag system warning light illuminates for

approx. 6 s

and goes out.



If the air bag system warning light does not operate, refer to

RESTRAINTS -- ON-BOARD

DIAGNOSTIC

system (air bag system) and perform inspection of the system.

PASSENGER-SIDE AIR BAG MODULE REMOVAL NOTE

1. Remove the passenger-side air bag module in the order indicated below.

1. Disengage the tab locks by sliding the passenger-side air bag module upward.

2. Slide the passenger-side air bag module rearward.

3. Remove the passenger-side air bag module by pulling it from the backside and then down.

Fig. 13: View Of Passenger-Side Air Bag Module

Courtesy of MAZDA MOTORS CORP.

CONNECTOR REMOVAL NOTE

1. Using a flathead screwdriver, pry out the connector stopper plate.

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 15

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды