Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 791 | Manualshive

Страница: 791 / 2244

background image

Fig. 45: Measuring Probe Of Dial Gauge Attached To End Of One Of Ring Gear Teeth

Courtesy of MAZDA MOTORS CORP.

8. Secure the drive pinion and measure the backlash of the ring gear.

Backlash of drive pinion and ring gear

Standard: 0.09-0.11 mm {0.0035-0.0043 in}

Minimum value: 0.05 mm {0.0020 in} or more

Variance: 0.07 mm {0.0028 in} or less

NOTE:



Measure the backlash at 4 locations around the ring gear. Make sure
all of the 4 locations are within specification, and the minimum value
for the 4 locations is 0.05 mm {0.0020 in} or more and the variance is
0.07 mm {0.0028 in} or less

2007 Mazda MX-5 Miata Sport

2007 DRIVELINE/AXLES Differential - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:11:17 PM

Page 47

© 2005 Mitchell Repair Information Company, LLC.

«
...
789
790
791
792
793
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Metra Electronics Страницы: 14

Бренд: Baja Designs Страницы: 6

Бренд: Porsche Страницы: 144

2012 Escalade Hybrid

Бренд: Cadillac Страницы: 90

Бренд: Ultra-tow Страницы: 14

Бренд: Mercedes-Benz Страницы: 121

Бренд: Menabo Страницы: 8

Бренд: Camtree Страницы: 5

Бренд: Brodit Страницы: 2

Бренд: Power Fist Страницы: 12

Бренд: EAL Страницы: 7

DBALL2-HYUNDAI9

Бренд: Xpresskit Страницы: 13

2011 3500 Chassis Cab

Бренд: RAM Страницы: 92

Бренд: Menabo Страницы: 12

Бренд: Prorack Страницы: 20

Бренд: tams elektronik Страницы: 19

Бренд: Mercedes-Benz Страницы: 91

Бренд: Carcomm Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды