manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Спортивный автомобиль Mazda MX-5 Miata Sport 2007 года выпуска - это мощное сочетание стиля и производительности. Для того чтобы получить руководство по эксплуатации, вы можете бесплатно скачать его с нашего веб-сайта. manualshive.com - ваш источник для скачивания руководств в формате PDF.

Поделиться
Скачать
background image

PARKING LIGHT BULB REMOVAL/INSTALLATION 

1. Remove the battery cover.  

2. Disconnect the negative battery cable. (See 

BATTERY REMOVAL/INSTALLATION [LF]

 .)  

3. Disconnect the connector.  

4. Remove the socket, then remove the parking light bulb.  

5. Install in the reverse order of removal. 

headlight control module terminal F and 
ground for following: 

Short to power supply  

Open circuit  

Is the wiring harness normal?  

No

Replace the related wiring harness.

7

VERIFY WHETHER MALFUNCTION IS IN 
DISCHARGE HEADLIGHT BULB OR 
DISCHARGE HEADLIGHT CONTROL 
MODULE

 

Install the discharge headlight low bulb 
(previously verified as illuminating 
normally). 

(See 

HEADLIGHT BULB 

REMOVAL/INSTALLATION

 .) 

Connect the discharge headlight control 
module connector.  

Turn the headlight switch to the 
HEADLIGHT (LO) position.  

Does the headlight (low-beam) illuminate?  

Yes System inspection completed.

No

Replace the front combination light. (See 

FRONT COMBINATION LIGHT 

REMOVAL/INSTALLATION

 .)

 

2007 Mazda MX-5 Miata Sport 

2007 ACCESSORIES & BODY, CAB Lighting Systems - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:27:42 PM

Page 18 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Бренд: Eaton Страницы: 65
Chevrolet Camaro 12000 1968 Series Factory Assembly Instruction Manual preview
Camaro 12000 1968 Series
Бренд: Chevrolet Страницы: 455
Cargo Floor CF500 SL-2 Replacement Instructions Manual preview
CF500 SL-2
Бренд: Cargo Floor Страницы: 16
Metra Electronics 99-5819 Installation Instructions Manual preview
99-5819
Бренд: Metra Electronics Страницы: 8
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Бренд: FVC Страницы: 8
Billien OBU 5050 Quick Installation Manual preview
OBU 5050
Бренд: Billien Страницы: 2
Lexus ES 2021 Quick Manual preview
ES 2021
Бренд: Lexus Страницы: 28
FALCON RIDGE CF-UFORCE-DRW01 Instructions For Installation And Care preview
CF-UFORCE-DRW01
Бренд: FALCON RIDGE Страницы: 6
Volvo V70 2014 Quick Manual preview
V70 2014
Бренд: Volvo Страницы: 16
Mercedes-Benz 2013 S-CLASS Owner'S Manual preview
2013 S-CLASS
Бренд: Mercedes-Benz Страницы: 493
Van Guard VG162S Fitting Instructions preview
VG162S
Бренд: Van Guard Страницы: 3
Waeco MagicWatch MW150 Installation And Operating Manual preview
MagicWatch MW150
Бренд: Waeco Страницы: 144
Brodit 810698 Installation Instructions preview
810698
Бренд: Brodit Страницы: 2
Over Armour Offroad TX-STAMP-4-TC01 Instructions For Installation And Care preview
TX-STAMP-4-TC01
Бренд: Over Armour Offroad Страницы: 4
Metra Electronics 99-8206 Installation Instructions Manual preview
99-8206
Бренд: Metra Electronics Страницы: 12
Chevrolet 2013 Duramax Diesel Owner'S Manual preview
2013 Duramax Diesel
Бренд: Chevrolet Страницы: 132
Jeep Compass 2013 User Manual preview
Compass 2013
Бренд: Jeep Страницы: 116
Jeep 2009 Wrangler Owenrs Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 502

Бренды по названию

Популярные бренды

Загрузить еще бренды