Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1033 | Manualshive

Страница: 1033 / 2244

background image

Fig. 42: Identifying PCM Harness Side Connector

Courtesy of MAZDA MOTORS CORP.

Open Circuit



If there is no continuity, there is an open circuit. Repair or replace the wiring harness.



MAP/boost air temperature sensor terminal A and PCM terminal 2AV



MAP/boost air temperature sensor terminal C and PCM terminal 2AU



MAP/boost air temperature sensor terminal D and PCM terminal 2AG

Short Circuit



If there is continuity, there is a short circuit. Repair or replace the wiring harness.



MAP/boost air temperature sensor terminal A and power supply.



MAP/boost air temperature sensor terminal C and body ground.



MAP/boost air temperature sensor terminal D and power supply.



MAP/boost air temperature sensor terminal D and body ground.

THROTTLE POSITION (TP) SENSOR INSPECTION [LF]

CAUTION:



This inspection procedure cannot be completed correctly if the
accelerator pedal position sensor has a malfunction. Before
performing this procedure, verify that any one of the DTCs related to

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Engine Control System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:41:10 PM

Page 68

© 2005 Mitchell Repair Information Company, LLC.

«
...
1031
1032
1033
1034
1035
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Back View Страницы: 168

DAF POWERCHOICE 250A

Бренд: Paccar Страницы: 20

Бренд: Farad Страницы: 8

Бренд: tams elektronik Страницы: 44

Бренд: Road Ranger Страницы: 22

Бренд: Draw tite Страницы: 4

Бренд: EFILive Страницы: 25

Бренд: Bestop Страницы: 4

ESCALADE ESV 2005

Бренд: Cadillac Страницы: 482

Бренд: curt Страницы: 4

Бренд: Scosche Страницы: 12

Бренд: Brainz Страницы: 2

Бренд: Reese Страницы: 21

Бренд: Nav TV Страницы: 11

Бренд: Nav TV Страницы: 8

Бренд: Haltech Страницы: 13

Бренд: Subaru Страницы: 786

Бренд: ULTIMATE SPEED Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды