Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2033

Страница: 2033 / 2244

NO.22 VIBRATION CONCERNS (ENGINE) [LF]

POSSIBLE CAUSE & DESCRIPTION (VIBRATION CONCERNS (ENGINE))

DIAGNOSTIC PROCEDURE

VIBRATION CONCERNS (ENGINE) DIAGNOSTIC PROCEDURE TABLE



If vehicle is not repaired or additional diagnostic information
is not available, replace the PCM.

(See

PCM REMOVAL/INSTALLATION [LF]

VIBRATION CONCERNS (ENGINE)

DESCRIPTION



Vibration from under hood or driveline

POSSIBLE CAUSE



Loose attaching bolts or worn parts



Components malfunction such as worn parts

STEP

INSPECTION

RESULTS

ACTION

Inspect the following
components for loose
attaching bolts or worn
parts:



Cooling fan



Drive belt and
pulleys



Generator



Engine mounts



Exhaust system
mounts

All items normal?

Yes

Inspect the following
systems:



Wheels



Driveline



Suspension

Readjust or retighten
engine mount installation
position.
Service if necessary for
other parts.



Verify test results.



If normal, return to diagnostic index to service any additional
symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [LF]



If malfunction remains, inspect related Service Bulletins and/or
On-line Repair Information and perform repair or diagnosis.



If vehicle is repaired, troubleshooting completed.



If vehicle is not repaired or additional diagnostic

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:10 PM

Page 100

«
...
2031
2032
2033
2034
2035
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды