Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 237 | Manualshive

Страница: 237 / 2244

background image

1. Turn the ignition switch to the LOCK position.

2. Remove the battery cover.

3. Disconnect the negative battery cable and wait for

1 min or more

. (See

BATTERY

REMOVAL/INSTALLATION [LF]

.)

4. Remove the glove compartment. (See

GLOVE COMPARTMENT REMOVAL/INSTALLATION

.)

5. Remove in the order indicated in

Fig. 12

.

system service warnings and cautions before handling the air bag
module. (See AIR BAG SYSTEM SERVICE WARNINGS .) (See AIR
BAG SYSTEM SERVICE CAUTIONS .)



If the passenger-side air bag module is installed with debris in the
module, it may be scattered when the air bag module operates
(deploys), causing injury. Verify that there is no debris in the
passenger-side air bag module before installation.



If a damaged passenger-side air bag module is installed, the vehicle
may be damaged or the passenger may be injured when the air bag
module operates (deploys). Verify that the passenger-side air bag
has no damage before installation.



Due to the adoption of 2-step deployment control in the passenger-
side air bag module, depending on the impact force, it is possible
that inflator No.2 might not deploy. In such cases, before disposing
of the air bag module, make sure to follow the inflator deployment
procedures and verify complete deployment of inflators No.1 and 2.

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 13

© 2005 Mitchell Repair Information Company, LLC.

«
...
235
236
237
238
239
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: K&M Страницы: 3

Бренд: Jackco Страницы: 11

Бренд: Kolpin Страницы: 25

Бренд: Romik Страницы: 6

Бренд: Caltrend Страницы: 2

Бренд: Audiovox Страницы: 1

EGR-3PVE-COLOUR

Бренд: EGR Страницы: 28

Бренд: PAC Страницы: 4

Бренд: C-KO Страницы: 4

Бренд: Honda Страницы: 268

Бренд: MBRP Страницы: 5

Бренд: Calix Страницы: 4

Бренд: SSV Works Страницы: 2

Бренд: Smappee Страницы: 28

OVER DRIVE PolyPRO 3 Car Cover

Бренд: Classic Accessories Страницы: 2

Бренд: Kargo Master Страницы: 7

Бренд: Directed Страницы: 24

Бренд: Kargo Master Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды