manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1064 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1064

1. Remove the battery cover.  

2. Remove the negative battery cable. (See 

BATTERY REMOVAL/INSTALLATION [LF]

 .)  

3. Disconnect the KS connector.  

4. Measure resistance between KS terminals A and B. 

If not within the specification, replace the KS. (See 

KNOCK SENSOR (KS) 

REMOVAL/INSTALLATION [LF]

 .)  

If the monitor item status/specification (reference) is not within the specification, even though the 
KS resistance is within the specification, perform the 

CIRCUIT OPEN/SHORT INSPECTION

.  

KS resistance

  

Approx. 4.87 megohms

  

CIRCUIT OPEN/SHORT INSPECTION 

1. Disconnect the PCM connector.  

2. Inspect the following wiring harnesses for an open or short circuit. (Continuity inspection) 

Fig. 72: Identifying Knock Sensor Harness Side Connector

 

2007 Mazda MX-5 Miata Sport 

2007 ENGINE PERFORMANCE Engine Control System - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:41:11 PM

Page 99 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов