manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Спортивный автомобиль Mazda MX-5 Miata Sport 2007 года выпуска - это мощное сочетание стиля и производительности. Для того чтобы получить руководство по эксплуатации, вы можете бесплатно скачать его с нашего веб-сайта. manualshive.com - ваш источник для скачивания руководств в формате PDF.

Поделиться
Скачать
background image

No

Go to the next step.

2

Is a rumbling or 
grinding noise present?

Yes

Inspect for the followings: 

Drive belt tension  

P/S fluid level  

No

Go to the next step.

3

Is a rattling noise 
present?

Yes

Inspect rattling location for 
loose parts.

No

Go to the next step.

4

Is a hissing noise 
present?

Yes

Inspect for the following: 

Vacuum leakage  

Spark plug looseness  

Intake-air system 
leakage  

No

Go to the next step.

5

Is a rapping or roar 
noise present?

Yes

Inspect looseness for 
followings: 

Dynamic dumper  

Intake-air system  

Exhaust system  

No

Go to the next step.

6

Is a knocking noise 
present?

Yes

Go to symptom 
troubleshooting "No.13 
Knocking/pinging". 
(See 

NO.13 

KNOCKING/PINGING-
ACCELERATION/CRUISE 
[LF]

 .)

No

If the noise comes from the 
engine internal, inspect for 
friction gear, timing chain or 
MLA noise.

7

Verify test results. 

If normal, return to diagnostic index to service any additional 
symptoms. 

(See 

ENGINE SYMPTOM TROUBLESHOOTING [LF]

 .) 

If malfunction remains, inspect related Service Bulletins and/or On-
line Repair Information and perform repair or diagnosis. 

If vehicle is repaired, troubleshooting completed.  

 

2007 Mazda MX-5 Miata Sport 

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:42:10 PM

Page 99 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

AC Schnitzer F40 Fitting Instructions Manual preview
F40
Бренд: AC Schnitzer Страницы: 16
Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Бренд: Eaton Страницы: 65
Allen Sports QR545 Instructions preview
QR545
Бренд: Allen Sports Страницы: 2
Porsche 911 GT3 - Owner'S Manual preview
911 GT3 -
Бренд: Porsche Страницы: 195
Whispbar K925W Fitting Instructions Manual preview
K925W
Бренд: Whispbar Страницы: 15
Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Бренд: Dynojet Страницы: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Бренд: Kuda-Phonebase Страницы: 3
Maserati Gransport Owner'S Manual preview
Gransport
Бренд: Maserati Страницы: 210
OnStar liveon Owner'S Manual preview
liveon
Бренд: OnStar Страницы: 22
Jeep Cherokee 2000 Service Manual preview
Cherokee 2000
Бренд: Jeep Страницы: 1528
Menabo JUZA Fitting Instructions Manual preview
JUZA
Бренд: Menabo Страницы: 12
Toyota SUPRA 1987 Electrical Wiring Diagram preview
SUPRA 1987
Бренд: Toyota Страницы: 165
Cadillac Fleetwood Brougham Sedan 1966 Owner'S Manual preview
Fleetwood Brougham Sedan 1966
Бренд: Cadillac Страницы: 56
Broadfeet RSLX-385-68S Installation Instructions preview
RSLX-385-68S
Бренд: Broadfeet Страницы: 2
Safe Fleet PRIME DESIGN HRR3-E-PM42 Manual preview
PRIME DESIGN HRR3-E-PM42
Бренд: Safe Fleet Страницы: 12
N.R. AUTOSEATS Top User Manual preview
Top
Бренд: N.R. AUTOSEATS Страницы: 8
Mopar 82214480 Manual preview
82214480
Бренд: Mopar Страницы: 17
Griffin Technology iTrip Bluetooth User Manual preview
iTrip Bluetooth
Бренд: Griffin Technology Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды