Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1794

Страница: 1794 / 2244

Fig. 4: Removing/Installing Main Fuse (With Torque Specifications)

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

IGNITION SWITCH REMOVAL/INSTALLATION

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

3. Remove the column cover. (See

COLUMN COVER REMOVAL/INSTALLATION

4. Remove in the order indicated in

Fig. 5

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Power Systems - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:28:36 PM

Page 4

«
...
1792
1793
1794
1795
1796
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды