Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1635 | Manualshive

Страница: 1635 / 2244

background image

Fig. 13: Identifying Headlight Bulb

Courtesy of MAZDA MOTORS CORP.

DISCHARGE HEADLIGHT CONTROL MODULE REMOVAL/INSTALLATION

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

.)

3. Remove the front combination light. (See

FRONT COMBINATION LIGHT

REMOVAL/INSTALLATION

.)

4. Remove screws.

5. Disconnect the connector.

6. Remove the discharge headlight control module.

7. Install in the reverse order of removal.

WARNING:



Incorrect servicing of the discharge headlights could result in
electrical shock. Before servicing the discharge headlights, always
refer to the discharge headlight service warnings. (See DISCHARGE
HEADLIGHT SERVICE WARNINGS .)

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Lighting Systems - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:27:42 PM

Page 14

© 2005 Mitchell Repair Information Company, LLC.

«
...
1633
1634
1635
1636
1637
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Camcar Страницы: 6

Бренд: Jeda Страницы: 8

Бренд: Jeep Страницы: 496

Бренд: GARO Страницы: 2

Бренд: Jackco Страницы: 11

Бренд: Calix Страницы: 5

Бренд: Roav Страницы: 10

2013 C-Class Coupe

Бренд: Mercedes-Benz Страницы: 388

Бренд: Standby Страницы: 10

MOLLE PANELS RAM 2500

Бренд: PUTCO Страницы: 4

Бренд: Westfalia Страницы: 18

AAB-P-RZR900-K2-001

Бренд: SuperATV Страницы: 3

10-8002-C11670C

Бренд: Saleen Страницы: 17

Quattroporte Automatic

Бренд: Maserati Страницы: 272

Escalade ESV 2014

Бренд: Cadillac Страницы: 508

Бренд: Hama Страницы: 2

PRIME DESIGN VRR-E-PM21

Бренд: Safe Fleet Страницы: 12

Бренд: Hummer Страницы: 502

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды