Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2113 | Manualshive

Страница: 2113 / 2244

background image

Fig. 42: Identifying Cutting Line And Pin

Courtesy of MAZDA MOTORS CORP.

REAR WINDOW GLASS INSTALLATION[DETACHABLE HARDTOP]

1. Cut away the old sealant using a razor so that a

1-2 mm {0.04-0.07 in}

thickness of sealant remains along

the perimeter of the frame.

2. If the sealant has come off completely in any one place, apply some primer after degreasing, and allow it

to dry for

approx. 30 min.

Then apply a

2 mm {0.08 in}

thickness of sealant.

3. Clean and degrease the perimeter

approx. 50 mm {1.97 in}

from the glass end and the bonding area on

the body.

4. Apply glass primer on the rear window glass, and body primer as shown in the figure. Allow it to dry for

approx. 30 min.

CAUTION:



Proper installation of the rear window glass may be difficult if sealant
is cracked or the glass is pushed out by air pressure when a door is
opened/closed with all the window glass closed. Leave all the
windows open until the rear window glass is installed completely.

WARNING:



Using a razor with bare hands can cause injury. Always wear
gloves when using a razor.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Glass/Windows/Mirrors - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:24:32 PM

Page 28

© 2005 Mitchell Repair Information Company, LLC.

«
...
2111
2112
2113
2114
2115
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Jeep Страницы: 5

Бренд: Jeep Страницы: 6

Grand Cherokee SRT 2014

Бренд: Jeep Страницы: 345

Grand Cherokee 2015

Бренд: Jeep Страницы: 236

Бренд: Jeep Страницы: 18

Бренд: Jeep Страницы: 24

Бренд: Jeep Страницы: 560

Бренд: Jeep Страницы: 525

Бренд: Jeep Страницы: 308

Бренд: Jeep Страницы: 86

Бренд: Jeep Страницы: 638

Бренд: Jeep Страницы: 9

Бренд: Jeep Страницы: 51

Бренд: Jeep Страницы: 4

Бренд: Jeep Страницы: 50

Grand Cherokee SRT 2014

Бренд: Jeep Страницы: 118

2014 Grand Cherokee

Бренд: Jeep Страницы: 24

Бренд: Jeep Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды