Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 609 | Manualshive

Страница: 609 / 2244

background image

1. Remove in the order indicated in

Fig. 7

.

2. Install in the reverse order of removal.

Fig. 7: Identifying Brake Pedal Components (With Torque Specifications)

Courtesy of MAZDA MOTORS CORP.

BRAKE PEDAL REMOVAL NOTE

one when replacing the power brake unit or the pedal, or performing
any procedure that changes the pedal stroke.



When replacing the brake pedal (AT), it is possible that the
installation of the interlock cable could become defective. Always
refer to the interlock cable installation note when replacing the brake
pedal. (See INTERLOCK CABLE INSTALLATION NOTE .)

NOTE:



When the brake switch connector is connected to the brake switch, the
clearance between the pedal and the brake switch is adjusted
automatically. However, this mechanism will only function one time.

2007 Mazda MX-5 Miata Sport

2007 BRAKES Conventional Brake System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:18:52 PM

Page 9

© 2005 Mitchell Repair Information Company, LLC.

«
...
607
608
609
610
611
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: JAC Страницы: 70

Бренд: ABL Страницы: 176

Бренд: ABL Страницы: 94

Бренд: Saab Страницы: 10

Wallbox eM4 Single

Бренд: ABL Страницы: 68

Бренд: Metra Electronics Страницы: 2

Бренд: Mazdaspeed Страницы: 8

Бренд: Caltrend Страницы: 2

Бренд: Audiovox Страницы: 1

EGR-3PVE-COLOUR

Бренд: EGR Страницы: 28

Road Ready Seat Protector

Бренд: Wagan Страницы: 12

Бренд: Chevrolet Страницы: 50

Бренд: Cadillac Страницы: 368

Бренд: Luverne Страницы: 3

Бренд: Navman Страницы: 27

Бренд: Kia Страницы: 58

Бренд: MAcarbon Страницы: 3

Бренд: Honda Страницы: 268

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды