Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 284 | Manualshive

Страница: 284 / 2244

background image

Fig. 59: Identifying Activation Switch

Courtesy of MAZDA MOTORS CORP.

11. Disconnect the

SSTs

(Deployment tool) from the

SSTs

(Adapter harness).

SIDE AIR BAG MODULE

1. Remove the side air bag module. (See

SIDE AIR BAG MODULE REMOVAL/INSTALLATION

.)

2. Install the nuts to the side air bag module as shown in

Fig. 60

, and connect the

SST

(Adapter harness).

WARNING:



Verify that air bag module operation (explosive) sound occurs
twice. If no operation (explosive) sound was heard or a single
operation (explosive) sound was heard, both inflators would
not have operated (deployed) properly. This may cause serious
injury if the air bag module operates (deploy) unexpectedly. If
the two operation (explosive) sounds are not heard, perform
Step 8 again. If a total of two operation (explosive) sounds
cannot be verified even though Step 8 is performed again,
leave the air bag module alone for 30 min or more before
approaching it again.



The air bag module is very hot immediately after it is operated
(deployed). You can be burned. Do not touch the air bag
module for at least 15 min after deployment.

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 60

© 2005 Mitchell Repair Information Company, LLC.

«
...
282
283
284
285
286
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: AC Schnitzer Страницы: 16

Бренд: Oldsmobile Страницы: 354

PRIME DESIGN HRR-369-E-UM3-96

Бренд: Safe Fleet Страницы: 12

Бренд: Kocchi's Страницы: 4

Бренд: Honda Страницы: 22

Бренд: Mercedes-Benz Страницы: 494

Бренд: ROADGEAR Страницы: 2

Бренд: Whispbar Страницы: 14

Бренд: BabySafe Страницы: 43

Бренд: E-Lead Страницы: 11

Бренд: Ford Страницы: 46

Бренд: Chevrolet Страницы: 103

Бренд: Peak Страницы: 8

Бренд: Renault Страницы: 239

Бренд: Comelit Страницы: 20

BLADE-AL-TL5-EN

Бренд: Automotive Data Solutions Страницы: 27

F-150 Hybrid 2021

Бренд: Ford Страницы: 32

Бренд: Chevrolet Страницы: 402

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды