Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1676

Страница: 1676 / 2244

on/off

switch

switch to
the ON
position.

Dimmer
switch at
LO

B+

INSPECTION



Related wiring
harness

Front fog light
switch ON/OFF

Front fog
light switch

Light
switch at
2nd
position

Front fog
light
switch is
on.

1.0 or less



Light switch (See

LIGHT SWITCH
INSPECTION



Related wiring
harness

Front fog
light
switch is
off.

B+

Flash-to-pass

Light
switch

Turn the
ignition
switch to
the ON
position.

Flash-to-
pass
activated.

1.0 or less



Light switch (See

LIGHT SWITCH
INSPECTION



Related wiring
harness

Flash-to-
pass not
activated.

B+

Front fog light
relay operation

Front fog
light relay

Light
switch at
2nd
position
and
dimmer
switch at
LO

Front fog
light
switch is
on.

1.0 or less



FOG 15 A fuse



Front fog light relay
(See

RELAY

INSPECTION



Related wiring
harness

Front fog
light
switch is
off.

B+

Headlight
(RH)
operation (high-
beam)

Headlight
(high-
beam)

Light
switch at
2nd
position

Dimmer
switch at
LO

1.0 or less



Headlight (RH)



Related wiring
harness

Dimmer
switch at
HI

1.0 or less

Headlight
(LH)
operation (high-
beam)

Headlight
(high-
beam)

Light
switch at
2nd
position

Dimmer
switch at
LO

1.0 or less



Headlight (LH)



Related wiring
harness

Dimmer
switch at
HI

B+

Ground

GND

Under any condition:
Check for continuity
to ground.

Continuity

GND

Headlight
(RH)
operation (high-
beam)

Headlight
(high-
beam)

Light
switch at
2nd
position

Dimmer
switch at
LO

1.0 or less



Headlight (RH)



Related wiring
harness

Dimmer
switch at

B+

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Lighting Systems - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:27:42 PM

Page 55

«
...
1674
1675
1676
1677
1678
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды