manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 927 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 927

Fig. 14: Removing Bracket From EVAP System Leak Detection Pump

 

Courtesy of MAZDA MOTORS CORP.

 

8. Install in the reverse order of removal.  

EVAPORATIVE HOSE INSTALLATION NOTE 

1. Fit the evaporative hose onto the respective fittings, and install clamps as shown in 

Fig. 15

. 

1. Insert the evaporative hose securely to the nipple.  

2. Inspect the evaporative hose for damage and deformation. 

 

2007 Mazda MX-5 Miata Sport 

2007 ENGINE PERFORMANCE Emission System - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:38:04 PM

Page 13 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов