Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1732

Страница: 1732 / 2244



Verify the continuity between power
retractable hardtop control module
terminal 3F and ground.



Is there continuity?

INSPECT TO SEE WHETHER
MALFUNCTION IS IN DECK PANEL
CLOSE POSITION SWITCH OR
ELSEWHERE



Monitor the power retractable hardtop
control module PID DECK_CL using
the M-MDS when the position where
the deck panel could not operate.



Is the monitor value ON (deck panel
fully closed)?

Yes

Go to the next step.

Go to step 10.

INSPECT DECK PANEL CLOSE
POSITION SWITCH



Inspect the deck panel close position
switch. (See

DECK PANEL LIMIT

SWITCH INSPECTION



Is the deck panel close position
switch normal?

Yes

Go to the next step.

Replace the deck panel limit switch. (See

DECK PANEL LIMIT SWITCH
REMOVAL/INSTALLATION

INSPECT DECK PANEL CLOSE
POSITION SWITCH WIRING
HARNESS



Turn the ignition switch to the LOCK
position.



Disconnect the power retractable
hardtop control module (16-pin) and
the deck panel close position switch
connectors.



Verify that the continuity between the
power retractable hardtop control
module terminal 3F and ground.



Is there any continuity?

Yes

Adjust the deck panel close position
switch installation.

Repair for a short to the ground circuit.

10*

INSPECT DECK PANEL MOTOR
WIRING HARNESS



Turn the ignition switch to the LOCK
position.



Disconnect the power retractable
hardtop control module (16-pin, 24-

Yes

Repair or replace malfunctioning part.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Symptom Troubleshooting (Power Retractable Hardtop) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:25:58 PM

Page 18

«
...
1730
1731
1732
1733
1734
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды