Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 344

Страница: 344 / 2244

3. Connect the

SST

(Deployment tool) to the

SST

(Adapter harness).

4. Connect the

SST

(Deployment tool) to the battery. Connect the power supply red clip to the positive

battery terminal, and the black clip to the negative battery terminal.

5. Verify that the red lamp on the

SST

(Deployment tool) is illuminated.

6. Verify that all persons are standing

at least 6 m {20 ft}

away from the vehicle.

Fig. 43: Connecting SST (Deployment Tool) To SST (Adapter Harness)

Courtesy of MAZDA MOTORS CORP.

7. Press the activation switch on the

SST

(Deployment tool) to operate (deploy) the side air bag module.

8. Disconnect the

SSTs

(Deployment tool) from the

SSTs

(Adapter harness).

2007 Mazda MX-5 Miata Sport

2007 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:12:56 PM

Page 44

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды