Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1048 | Manualshive

Страница: 1048 / 2244

background image

3. Disconnect the CMP sensor connector.

4. Remove the CMP sensor installation bolt.

5. Remove the CMP sensor from the cylinder head cover.

Fig. 57: Identifying CMP Sensor

Courtesy of MAZDA MOTORS CORP.

6. Install in the reverse order of removal.

CMP sensor tightening torque

5.5-7.5 N.m {56-76 kgf.cm, 49-66 in.lbf}

CAMSHAFT POSITION (CMP) SENSOR INSPECTION [LF]

are no metal shavings adhering as they can cause the sensor
output signal to malfunction from fluctuation in magnetic flux
resulting in a deterioration in engine control. Cover a removed
CMP sensor in plastic to protect it from foreign material
adhering to it.

NOTE:



Before performing the following inspection, make sure to follow the
procedure as indicated in the troubleshooting flow diagram. (See
TROUBLESHOOTING PROCEDURE .)

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Engine Control System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:41:10 PM

Page 83

© 2005 Mitchell Repair Information Company, LLC.

«
...
1046
1047
1048
1049
1050
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Camoplast Страницы: 60

Бренд: Garmin Страницы: 2

Бренд: IAME Страницы: 17

Brute Strength 12057.0271

Бренд: Quadratec Страницы: 6

Бренд: Yakima Страницы: 8

Бренд: Subaru Страницы: 21

Бренд: A-Tach Страницы: 2

Бренд: RAM Страницы: 148

Бренд: Hamron Страницы: 36

Бренд: Saab Страницы: 37

Telescoping Computer Base C-TCB-34

Бренд: Havis-Shields Страницы: 1

Бренд: PEUGEOT Страницы: 107

Бренд: Acura Страницы: 19

Бренд: Ford Страницы: 325

Бренд: MayPole Страницы: 3

Бренд: Prorack Страницы: 14

Бренд: Alpine Страницы: 70

Бренд: Chevrolet Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды