Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1168

Страница: 1168 / 2244

Fig. 8: Identifying Audio Amplifier (With Torque Specifications)

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

POWER RETRACTABLE HARDTOP

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

3. Remove the following parts:

1. Console (See

CONSOLE REMOVAL/INSTALLATION

2. Quarter trim (See

QUARTER TRIM REMOVAL/INSTALLATION

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Entertainment - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:34:33 PM

Page 10

«
...
1166
1167
1168
1169
1170
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды