Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 747

Страница: 747 / 2244

Fig. 3: Identifying Oil Fill Level

Courtesy of MAZDA MOTORS CORP.

Differential oil

Grade: API service GL-5

Viscosity: SAE 90, SAE 80W-90, SAE 75W-90 (Not available from Mazda)

5. Install the oil-fill plug with a new washer and tighten.

Tightening torque

39.2-53.9 N.m {4.00-5.49 kgf.m, 29.0-39.7 ft.lbf}

DIFFERENTIAL OIL REPLACEMENT

1. Park the vehicle on level ground.

2. Remove the oil-fill plug.

3. Remove the drain plug and drain the oil.

2007 Mazda MX-5 Miata Sport

2007 DRIVELINE/AXLES Differential - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:11:17 PM

Page 3

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 747 / 2244

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы: