manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1644 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1644

Fig. 20: Identifying Fasteners

 

Courtesy of MAZDA MOTORS CORP.

 

5. Disconnect the front fog light connector.  

6. Remove the bolt, then remove the front fog light.  

7. Install in the reverse order of removal.  

8. Adjust the front fog light aiming. (See 

FRONT FOG LIGHT AIMING

.) 

 

2007 Mazda MX-5 Miata Sport 

2007 ACCESSORIES & BODY, CAB Lighting Systems - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:27:42 PM

Page 23 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов