Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2109

Страница: 2109 / 2244

Fig. 35: Identifying Sections For Applying Primer

Courtesy of MAZDA MOTORS CORP.

11. Apply sealant to the area of the glass surface as shown in the figure.

12. Insert the windshield locator pins to the body and install the windshield.

Fig. 36: Applying Sealant To Glass Surface

Courtesy of MAZDA MOTORS CORP.

13. Verify that the clearance of the A-pillar is within the range shown in the figure, and press along the

perimeter of the glass.

14. Install the following parts:

1. A-pillar trim (See

A-PILLAR TRIM REMOVAL/INSTALLATION

2. Map light (See

MAP LIGHT REMOVAL/INSTALLATION

3. Front header trim (See

FRONT HEADER TRIM REMOVAL/INSTALLATION

4. Rearview mirror (See

REARVIEW MIRROR REMOVAL/INSTALLATION

..)

CAUTION:



To prevent weakening of the primer adhesion, keep the bonding
surface free of dirt, moisture, and grease. Do not touch the
surface with your hand.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Glass/Windows/Mirrors - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:24:31 PM

Page 24

«
...
2107
2108
2109
2110
2111
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды