manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1172 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1172

Fig. 12: Identifying Door Speaker Connector & Terminals

 

Courtesy of MAZDA MOTORS CORP.

 

DOOR UPPER SPEAKER INSPECTION 

1. Inspect for resistance between the door upper speaker terminals using an ohmmeter. 

If the resistance is not within the specification, replace the door upper speaker.  

Fig. 13: Door Upper Speaker Continuity Table

 

2007 Mazda MX-5 Miata Sport 

2007 ACCESSORIES & BODY, CAB Entertainment - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:34:33 PM

Page 14 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов