Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2050 | Manualshive

Страница: 2050 / 2244

background image

Are all above items
normal?

No

Replace the fuel injector.

9

Is the air cleaner
element free of
clogging?

Yes

Go to the next step.

No

Replace the air cleaner element.

10

Perform the spark test.
(See

SPARK TEST

.)

Is strong blue spark
visible at each cylinder?

Yes

Go to the next step.

No

Repair or replace the
malfunctioning part.

11

Install the fuel pressure
gauge between the fuel
filter and fuel
distributor.
Short check connector
terminal F/P to body
GND using a jumper
wiring.
Turn the ignition switch
to the ON position
(Engine off).
Is the fuel line pressure
correct with ignition
switch at ON?
(See

FUEL LINE

PRESSURE
INSPECTION [LF]

.)

Yes

Go to the next step.

No

Zero or low:

Inspect the fuel pump relay and
fuel pump circuit.
Inspect the fuel line for
clogging.
If there is no malfunction,
replace the fuel pump unit.
(See

FUEL PUMP UNIT

REMOVAL/INSTALLATION
[LF]

.)

High:

Replace the fuel pump unit.
(See

FUEL PUMP UNIT

REMOVAL/INSTALLATION
[LF]

.)

12

Inspect the following
PIDs:



ECT



O2S11 (When
engine can be
started.)



O2S12 (When
engine can be
started.)



MAF

(See

PCM

INSPECTION [LF]

.)

Are PIDs normal?

Yes

Go to the next step.

No

Repair or replace the
malfunctioning part.

13

Perform the purge
control inspection.
(When engine can be

Yes

Go to the next step.

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:11 PM

Page 117

© 2005 Mitchell Repair Information Company, LLC.

«
...
2048
2049
2050
2051
2052
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

GRAND CHEROKEE 2023

Бренд: Jeep Страницы: 108

Бренд: Barker Страницы: 2

Бренд: Ultra-tow Страницы: 14

Бренд: Mercedes-Benz Страницы: 121

Бренд: Menabo Страницы: 8

Бренд: Camtree Страницы: 5

For 1985-1992 GM Cars and Trucks 17933

Бренд: Edelbrock Страницы: 4

Autostacker PL-6SR

Бренд: BendPak Страницы: 104

Бренд: MVG Страницы: 18

2917 Nstallation

Бренд: Edelbrock Страницы: 1

Бренд: Conrad Страницы: 50

Бренд: Volvo Страницы: 16

EPS-LD SafePark

Бренд: Tobe Страницы: 2

Бренд: Curt Group Страницы: 3

Бренд: Juna Страницы: 10

Бренд: Lexus Страницы: 6

Бренд: HUSKY LINERS Страницы: 4

Бренд: iOttie Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды