Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1131

Страница: 1131 / 2244

Fig. 59: Identifying Crankshaft Pulley Bolt

Courtesy of MAZDA MOTORS CORP.

4. Install the

SSTs

to the crankshaft pulley, lock the crankshaft against rotation.

5. Tighten the crankshaft pulley lock bolt in the order shown in

Fig. 60

using the following two steps.

1. Tighten to

96-104 N.m {9.8-10.6 kgf.m, 70.9-76.7 ft.lbf}

2. Tighten

87°-93°

2007 Mazda MX-5 Miata Sport

2007 ENGINE Mechanical - MX-5

Microsoft

Thursday, July 09, 2009 3:21:51 PM

Page 65

«
...
1129
1130
1131
1132
1133
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды