Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 195

Страница: 195 / 2244

(exterior, rear) (-
)

antenna
(exterior,
rear)

condition: Inspect
for continuity to
keyless antenna.

Continuity detected

keyless antenna
(exterior, rear)

keyless antenna
(interior, trunk)
(+)

keyless
antenna
(interior,
trunk)

Under any
condition: Inspect
for continuity to
keyless antenna.

Continuity detected

keyless antenna
(interior, trunk)

keyless antenna
(interior, trunk)
(-)

keyless
antenna
(interior,
trunk)

Under any
condition: Inspect
for continuity to
keyless antenna.

Continuity detected

keyless antenna
(interior, trunk)

keyless antenna
(interior, rear)
(+)

keyless
antenna
(interior, rear)

Under any
condition: Inspect
for continuity to
keyless antenna.

Continuity detected

keyless antenna
(interior, rear)

keyless antenna
(interior, rear) (-)

keyless
antenna
(interior, rear)

Under any
condition: Inspect
for continuity to
keyless antenna.

Continuity detected

keyless antenna
(interior, rear)

keyless antenna
(interior, middle)
(+)

keyless
antenna
(interior,
middle)

Under any
condition: Inspect
for continuity to
keyless antenna.

Continuity detected

keyless antenna
(interior, middle)

keyless antenna
(interior, middle)
(-)

keyless
antenna
(interior,
middle)

Under any
condition: Inspect
for continuity to
keyless antenna.

Continuity detected

keyless antenna
(interior, middle)

IG1

ENGINE 10
A fuse

Ignition switch is at
ON position

B+

ENGINE 10 A fuse

Ignition switch is at
LOCK or ACC
position

1.0 or less

GND

body ground

Under any
condition: Inspect
for continuity to
ground.

Continuity detected GND

Security light

Instrument
cluster

Under any
condition: Inspect
for continuity to
instrument cluster.

Continuity detected Instrument cluster

keyless antenna
(interior, front)
(+)

keyless
antenna
(interior,
front)

Under any
condition: Inspect
for continuity to
keyless antenna.

Continuity detected

keyless antenna
(interior, front)

keyless antenna keyless

Under any

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Advanced Keyless System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:36:54 PM

Page 36

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды