Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 2111

Страница: 2111 / 2244

Fig. 38: Identifying Lip With Section A-A

Courtesy of MAZDA MOTORS CORP.

10. Apply protective tape along the edge of the body.

Fig. 39: Identifying Protective Tape On Edge Of Body

Courtesy of MAZDA MOTORS CORP.

11. Insert the SST (piano wire), which has been cut to sufficient length from inside the vehicle.

NOTE:



Overlap and adhere the protective tape to the corners to prevent
damage.

WARNING:



Using the SST (piano wire) with bare hands can cause injury.
Always wear gloves when using the SST (piano wire).

NOTE:



Before removing the rear window glass from the body, mark the
position of the glass by affixing tape to the glass and body panel.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Glass/Windows/Mirrors - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:24:32 PM

Page 26

«
...
2109
2110
2111
2112
2113
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды