manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1191 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1191

Fig. 36: Removing Driver-Side Air Bag Module

 

Courtesy of MAZDA MOTORS CORP.

 

6. Install in the reverse order of removal.  

AUDIO CONTROL SWITCH INSPECTION 

1. Verify the resistance and continuity between the audio control switch terminals. 

If the resistance and continuity are not as indicated in the tables, replace the audio control switch.  

Fig. 37: Audio Control Switch Continuity Table

 

Courtesy of MAZDA MOTORS CORP.

 

2007 Mazda MX-5 Miata Sport 

2007 ACCESSORIES & BODY, CAB Entertainment - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:34:33 PM

Page 33 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов