Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1899 | Manualshive

Страница: 1899 / 2244

background image

2007 ENGINE

Starting System - MX-5 Miata

STARTING SYSTEM LOCATION INDEX [LF]

Fig. 1: Identifying Location Of Starting System Components

Courtesy of MAZDA MOTORS CORP.

STARTER REMOVAL/INSTALLATION [LF]

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

.)

3. Remove the side cover. (LH)

WARNING:



Remove and install all parts when the engine is cold, otherwise they
can cause severe burns or serious injury.



When the battery cables are connected, touching the vehicle body
with starter terminal B will generate sparks. This can cause personal
injury, fire, and damage to the electrical components. Always
disconnect the negative battery cable before performing the
following operation.

2007 Mazda MX-5 Miata Sport

2007 ENGINE Starting System - MX-5 Miata

2007 Mazda MX-5 Miata Sport

2007 ENGINE Starting System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:06:51 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Thursday, July 09, 2009 3:06:56 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

«
...
1897
1898
1899
1900
1901
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: UnderCover Страницы: 16

Titanium Series

Бренд: Fass Страницы: 13

Бренд: Lancia Страницы: 386

Бренд: Ultra Start Страницы: 8

Бренд: Pivot Страницы: 4

Бренд: Metra Electronics Страницы: 2

10-8002-C11998B

Бренд: Saleen Страницы: 12

2013 Buick Verano

Бренд: Buick Страницы: 5

Бренд: GMC Страницы: 425

Wireless Handsfree Car Kit

Бренд: Wagan Страницы: 20

Бренд: Alfa Romeo Страницы: 8

Бренд: Fast Master Products Страницы: 13

Бренд: Yutrax Страницы: 8

Бренд: Caraudio-Systems Страницы: 9

Бренд: ECS Страницы: 4

Бренд: Whispbar Страницы: 15

1999 Crown Victoria

Бренд: Ford Страницы: 208

84 64 0 025 810

Бренд: BMW Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды