Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 264 | Manualshive

Страница: 264 / 2244

background image

connector) of the

SST

(Adapter harness), and

after 3 s

, press the activation switch on the other

SST

(Deployment tool) to operate (deploy) the air bag module (both inflators).

Fig. 38: Identifying Activation Switch

Courtesy of MAZDA MOTORS CORP.

9. Disconnect the

SSTs

(Deployment tool) from the

SSTs

(Adapter harness).

PASSENGER-SIDE AIR BAG MODULE

WARNING:



Verify that air bag module operation (explosive) sound occurs
twice. If no operation (explosive) sound was heard or a single
operation (explosive) sound was heard, both inflators would
not have operated (deployed) properly. This may cause serious
injury if the air bag module operates (deploy) unexpectedly. If
the two operation (explosive) sounds are not heard, perform
Step 8 again. If a total of two operation (explosive) sounds
cannot be verified even though step 8 is performed again, leave
the air bag module alone for 30 min or more before
approaching it again.



The air bag module is very hot immediately after it is operated
(deployed). You can get burned. Do not touch the air bag
module for at least 15 min after deployment.

WARNING:



The passenger-side air bag module is a dual inflator type. If one

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 40

© 2005 Mitchell Repair Information Company, LLC.

«
...
262
263
264
265
266
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: U.S. General Страницы: 5

Бренд: Suzuki Страницы: 353

Бренд: Torklift Страницы: 16

10-8002-C11998B

Бренд: Saleen Страницы: 12

2013 Buick Verano

Бренд: Buick Страницы: 5

Бренд: PEUGEOT Страницы: 128

Бренд: Schumacher Electric Страницы: 87

2009 ESCALADE ESV

Бренд: Cadillac Страницы: 602

Бренд: Honda Страницы: 208

Бренд: AA Products Страницы: 4

Escalade ESV 2014

Бренд: Cadillac Страницы: 508

Бренд: Hama Страницы: 2

autoSteady AS101

Бренд: Enduro Страницы: 48

Бренд: Saab Страницы: 288

Бренд: Sunsky Страницы: 9

STO N SHO SNS 144

Бренд: Big Mikes Performance Parts Страницы: 7

Бренд: Lincoln Страницы: 10

Бренд: Yakima Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды