Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1564 | Manualshive

Страница: 1564 / 2244

background image

Fig. 24: Removing Front Header Trim

Courtesy of MAZDA MOTORS CORP.

INSTALLATION

1. Install the pin A and clip B.

2. Pull down the sunvisor on the right, then install pin C and clips D.

3. Pull down the sunvisor on the left, then install pin E and clips F.

4. Install the screw.

5. Install the A-pillar trim. (See

A-PILLAR TRIM REMOVAL/INSTALLATION

.)

6. Install the map light. (See

MAP LIGHT REMOVAL/INSTALLATION

.)

7. Install the female wedge. (See

CONVERTIBLE TOP DISASSEMBLY/ASSEMBLY

.)

CAUTION:



Do not twist or drop the front header trim, otherwise the vanity mirror
could be damaged.



If the front header trim is installed with the sunvisor pulled up, the
vanity mirror could be damaged. Always install the front header trim
with the sunvisor pulled down.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Interior Trim - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:29:26 PM

Page 23

© 2005 Mitchell Repair Information Company, LLC.

«
...
1562
1563
1564
1565
1566
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Harbor Freight Tools Страницы: 4

GRAND CHEROKEE 2023

Бренд: Jeep Страницы: 108

Бренд: OEM Tools Страницы: 4

Бренд: DEFA Страницы: 9

Slim Line LED Light Grille Kit

Бренд: rough country Страницы: 8

Indigo MANZA QUADRAJET 90

Бренд: TATA Motors Страницы: 10

LeisureWize EMOVE EM303A

Бренд: Streetwize Страницы: 20

Бренд: kincrome Страницы: 6

Бренд: B-Speech Страницы: 4

Бренд: Actia Страницы: 102

Бренд: Bilstein Страницы: 7

CF-UFORCE-DRW01

Бренд: FALCON RIDGE Страницы: 6

Бренд: CITROEN Страницы: 86

Бренд: SpeedTech Lights Страницы: 2

Бренд: TIS Страницы: 6

Бренд: Saab Страницы: 9

Бренд: Kargo Master Страницы: 14

MULTI VEHICLE MOUNT MVM-45-05

Бренд: Bracketron Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды