Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 2244

background image

Fig. 4: Locating DLC-2 Connector

Courtesy of MAZDA MOTORS CORP.

ACTIVE COMMAND MODES PROCEDURE

1. Connect the M-MDS to the DLC-2.

2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.



When using the IDS (laptop PC)



Select the "Toolbox" tab.



Select "DataLogger".



Select "Modules".



Select "ABS".



When using the PDS (Pocket PC)



Select "Modules Tests".

NOTE:

The PID data screen function is used for monitoring the calculated value.
Therefore, if the monitored value of the output parts is not within specification,
inspection of the monitored value of input parts corresponding to applicable
output part control is necessary. In addition, because the system does not
display output part malfunction as abnormality in the monitored value, it is
necessary to inspect the output part individually using a active command
modes function.

2007 Mazda MX-5 Miata Sport

2007 BRAKES On-Board Diagnostic (ABS) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:17:55 PM

Page 5

© 2005 Mitchell Repair Information Company, LLC.

«
...
125
126
127
128
129
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: B-Speech Страницы: 18

Бренд: AccuAir Страницы: 40

Бренд: Peak Страницы: 10

Бренд: Subaru Страницы: 34

Бренд: Gator Страницы: 8

Бренд: Volvo Страницы: 24

Бренд: Hella Страницы: 21

Бренд: Atera Страницы: 3

Бренд: Black Horse Страницы: 5

Бренд: Mazda Страницы: 3

Бренд: Brink Страницы: 26

Бренд: Prorack Страницы: 14

Бренд: TomTom Страницы: 22

Бренд: BMW Страницы: 40

Бренд: iQOS Страницы: 4

Бренд: Quadratec Страницы: 8

MKZ HYBRID 2016

Бренд: Lincoln Страницы: 10

Бренд: J Communications Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды