Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1968

Страница: 1968 / 2244

NO.6 CRANKS NORMALLY BUT WILL NOT START [LF]

POSSIBLE CAUSE & DESCRIPTION (CRANKS NORMALLY BUT WILL NOT START [LF])

Plug opening end of
vacuum hose.
Start the engine.
Is the engine stall now
eliminated?

Go to the next step.

Is air leakage felt or
heard at intake-air
system components
while racing the engine
to higher speed?

Yes

Repair or replace the
malfunctioning part.

Go to the next step.

Inspect the engine
condition while tapping
EGR valve housing.
Does the engine
condition improve?

Yes

Replace the EGR valve.

Go to the next step.

Inspect variable valve
timing control system
operation.
(See

VARIABLE

VALVE TIMING
CONTROL SYSTEM
OPERATION
INSPECTION

Does variable valve
timing control function
properly?

Yes

Go to the next step.

Repair or replace the
malfunctioning parts according
to variable valve timing control
system operation inspection
results.

Is the engine
compression correct?

Yes

Inspect the valve timing.

Inspect for cause.



Verify test results.



If normal, return to diagnostic index to service any additional
symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [LF]



If malfunction remains, inspect related Service Bulletins and/or On-
line Repair Information and perform repair or diagnosis.



If vehicle is repaired, troubleshooting completed.



If vehicle is not repaired or additional diagnostic information
is not available, replace the PCM.

(See

PCM REMOVAL/INSTALLATION [LF]

2007 Mazda MX-5 Miata Sport

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:42:09 PM

Page 35

«
...
1966
1967
1968
1969
1970
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды