Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 2244

background image

Fig. 22: View Of Seat Track Position Sensor

Courtesy of MAZDA MOTORS CORP.

SEAT WEIGHT SENSOR CONTROL MODULE REMOVAL/INSTALLATION

1. Turn the ignition switch to the LOCK position.

2. Remove the battery cover.

3. Disconnect the negative battery cable and wait for

1 min or more

. (See

BATTERY

REMOVAL/INSTALLATION [LF]

.)

4. Remove in the order indicated in

Fig. 23

.

CAUTION:



When the seat weight sensor control module is replaced with a new
one, perform the seat weight sensor calibration using the WDS or
equivalent. (See SEAT WEIGHT SENSOR CALIBRATION .)

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 25

© 2005 Mitchell Repair Information Company, LLC.

«
...
247
248
249
250
251
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: RaceChip Страницы: 12

Бренд: Yakima Страницы: 11

Бренд: Whispbar Страницы: 15

Akerstroms Tx700

Бренд: LXE Страницы: 146

2003 Silhouette

Бренд: Oldsmobile Страницы: 466

Security Cage Kit

Бренд: Toro Страницы: 8

Бренд: Peiying Страницы: 32

Бренд: Brigade Страницы: 12

Бренд: Cadillac Страницы: 438

Бренд: XTC Страницы: 2

Бренд: HAKR Страницы: 10

Бренд: ECS Electronics Страницы: 14

Бренд: SAF-HOLLAND Страницы: 22

Бренд: Fcar Страницы: 15

Бренд: Guardsman Страницы: 3

Бренд: Kenwood Страницы: 6

Бренд: Kenwood Страницы: 2

ADS Determinator

Бренд: ALCOHOL DETECTION SYSTEMS Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды