Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 828 | Manualshive

Страница: 828 / 2244

background image

wheel does not rotate. While brake pressure is being reduced and an DSC HU/CM operation click sound
is heard, confirm that the wheel rotates.



Performing the inspection above determines the following:



The DSC HU/CM brake lines are normal.



The DSC HU/CM hydraulic system is not significantly abnormal (including DSC HU/CM).



The DSC HU/CM internal electrical parts (solenoid, motor and other parts) are normal.



The DSC unit and DSC HU/CM output system wiring harnesses (solenoid valve, relay
system) are normal.



However, the following items cannot be verified.



Malfunction with intermittent occurrence of the above items



Malfunction of DSC HU/CM input system wiring harnesses and parts



Extremely small leaks in the DSC HU/CM internal hydraulic system

DSC CONTROL INSPECTION

1. Perform "Preparation".

2. Connect the M-MDS to the DLC-2.

3. Set up an active command mode inspection according to the combination of commands below.

CAUTION:



To protect the DSC HU/CM, the solenoid valve and the pump
motor used during active command mode stay on for only 10 s
or less each time they are switched on.

2007 Mazda MX-5 Miata Sport

2007 BRAKES Dynamic Stability Control - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:17:05 PM

Page 5

© 2005 Mitchell Repair Information Company, LLC.

«
...
826
827
828
829
830
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

2011 grand cherokee

Бренд: Jeep Страницы: 22

2013 Grand Cherokee

Бренд: Jeep Страницы: 704

Бренд: Jeep Страницы: 558

Бренд: Porsche Страницы: 192

Бренд: Chevrolet Страницы: 356

Бренд: Ford Страницы: 272

Бренд: Pontiac Страницы: 376

Бренд: Jeep Страницы: 712

Бренд: Buick Страницы: 428

Бренд: EEZ RV Страницы: 31

Бренд: Yakima Страницы: 21

Бренд: Cadillac Страницы: 522

Бренд: Whispbar Страницы: 17

Бренд: Fiat Страницы: 24

Бренд: Valeo Страницы: 28

Бренд: Weltmann KFZ-Teile Страницы: 12

ZapCharger Portable C1

Бренд: ZAPTEC Страницы: 20

Бренд: Club Car Страницы: 286

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды