Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 158

Страница: 158 / 2244

DTC C1805 [ABS]

DTC C1805 POSSIBLE CAUSE TABLE

DIAGNOSTIC PROCEDURE

DTC C1805 DIAGNOSTIC PROCEDURE TABLE

output?

DTC C1805

Incorrect ABS HU/CM installed

DETECTION CONDITION



The programmed vehicle information and the
data received from the CAN do not
correspond.

POSSIBLE CAUSE



The correct ABS HU/CM is not installed.

STEP

INSPECTION

ACTION

VERIFY THAT THE
CORRECT ABS HU/CM
IS INSTALLED



Verify the part number
of the ABS HU/CM.



Is the part number
correct?

Yes

Go to the next step.

After replacing the ABS, go to Step 3.
(See

ABS HU/CM

REMOVAL/INSTALLATION

PERFORM
CONFIGURATION



Was configuration
performed normally?

Yes

Go to the next step.

Replace the ABS HU/CM, then go to
the next step.
(See

ABS HU/CM

REMOVAL/INSTALLATION

VERIFY DTC
TROUBLESHOOTING
COMPLETED



Make sure to
reconnect all
disconnected
connectors.



Clear the DTC from
the memory.



(See

CLEARING

DTCS
PROCEDURES



Is the same DTC
present?

Yes

Repeat the inspection from Step 1.
If the malfunction recurs, replace the
ABS HU/CM, then go to the next step.
(See

ABS HU/CM

REMOVAL/INSTALLATION

Go to the next step.

2007 Mazda MX-5 Miata Sport

2007 BRAKES On-Board Diagnostic (ABS) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:17:55 PM

Page 36

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды