Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 397 | Manualshive

Страница: 397 / 2244

background image

2006-08 TRANSMISSION

Automatic Transmission Overhaul - MX-5 Miata & RX-8

05-13 AUTOMATIC TRANSMISSION

AUTOMATIC TRANSMISSION DISASSEMBLY

Precaution

The following are precautions that must be followed performing removal/installation.

1. Handle electronic parts with care



Do not pull the wiring harness forcibly when disconnecting the connector. Unlock the first and pull
the connector.



When connecting the connector, verify that it is inserted until it is properly locked. (Verify that a
click sound is heard.)



Do not apply shock to electronic parts. Replace with new parts if they have been dropped or
subjected to shock.

2. Prevent foreign matter from penetrating



Be sure to remove foreign matter such as dust and sand from the automatic transaxle before
removing parts.



Protect removed parts from dust with an object such as a vinyl sheet.



Do not use cotton work gloves or shop rags as frayed strings might get caught in the unit. Work
with bare hands or use vinyl gloves.

3. Prevent scratching



Do not pry with a screwdriver forcibly. Slightly tap the case with a plastic hammer when separating
component cases at seams.



Do not pull the valve forcibly.



Be careful not to get the wiring harness caught between parts during installation.

4. Prevent incorrect or insufficient, installation or missing parts



Be careful not to install parts incorrectly or lose parts since there are similar types of O-rings, snap
rings, bearings and races. Be careful to for straighten parts and check their installation direction.



Be careful not to drop small parts such as check balls or lose them during installation.

5. Wash parts and apply oil



Wash each part before installing and dry using compressed air, and then apply the specified ATF
type JWS3309.



Soak discs in ATF type JWS3309 before installing. In particular, soak a new disc for

2 h or more

so that the oil seeps into the lining.



If the thrust bearing or race falls during installation, use a small amount of yellow petrolatum
grease.



Apply ATF type JWS3309 to contact and rotating surfaces.

2007 Mazda MX-5 Miata Sport

2006-08 TRANSMISSION Automatic Transmission Overhaul - MX-5 Miata & RX-8

2007 Mazda MX-5 Miata Sport

2006-08 TRANSMISSION Automatic Transmission Overhaul - MX-5 Miata & RX-8

Microsoft

Thursday, July 09, 2009 1:42:23 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Thursday, July 09, 2009 1:43:11 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

«
...
395
396
397
398
399
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: AA Products Страницы: 8

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 2

Бренд: Cadillac Страницы: 494

Бренд: Cadillac Страницы: 500

Бренд: Cadillac Страницы: 40

Бренд: Cadillac Страницы: 432

Бренд: Cadillac Страницы: 338

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 438

CHASSIS CAB 3500 2017

Бренд: RAM Страницы: 16

Бренд: Brodit Страницы: 2

Бренд: B-Speech Страницы: 24

Бренд: Subaru Страницы: 21

Бренд: Kargo Master Страницы: 19

PRIME DESIGN VBR3-FT31B

Бренд: Safe Fleet Страницы: 12

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Бренд: Havis-Shields Страницы: 1

Hatch-bag Luggage System

Бренд: Tabernus Peram Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды