Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 236

Страница: 236 / 2244

6. Turn the ignition switch to the ON position.

7. Verify that the air bag system warning light illuminates for

approx. 6 s

and goes out.



If the air bag system warning light does not operate normally, refer to

RESTRAINTS -- ON-

BOARD DIAGNOSTIC

system (air bag system) and perform inspection of the system.

CONNECTOR REMOVAL NOTE

1. Using a flathead screwdriver, pry out the connector stopper plate.

Fig. 11: Prying Out Connector Stopper Plate

Courtesy of MAZDA MOTORS CORP.

2. Disconnect the connector.

PASSENGER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION

WARNING:



Handling the air bag module improperly can accidentally deploy the
air bag module, which may seriously injure you. Read the air bag

2008 Mazda MX-5 Miata Grand Touring

2008 RESTRAINTS Air Bag System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:43:37 PM

Page 12

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды