Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 88

Страница: 88 / 2244

ADJUSTMENT SHIM SELECTION CHART

Backlash mm {in}

Selection

shim (No).

Shim thickness

mm {in}

Backlash mm {in}

Selection

shim (No).

Shim thickness

mm {in}

0.267-0.273

{0.01051-

0.01074}

1.15 {0.0452}

0.127-0.133

{0.00500-0.00523}

1.35 {0.0531}

0.260-0.266

{0.01023-

0.01047}

1.16 {0.0456}

0.120-0.126

{0.00472-0.00496}

1.36 {0.0535}

0.253-0.259

{0.00996-

0.01019}

1.17 {0.0460}

0.113-0.119

{0.00444-0.00468}

1.37 {0.0539}

0.246-0.252

{0.00968-

0.00992}

1.18 {0.0464}

0.106-0.112

{0.00417-0.00440}

1.38{0.0543}

0.239-0.245

{0.00940-

0.00964}

1.19 {0.0468}

0.099-0.105

{0.00389-0.00413}

1.39 {0.0547}

0.232-0.238

{0.00913-

0.00937}

1.20 {0.0472}

0.092-0.098 .087

{0.00362-0.00385}

1.40 {0.0551}

0.225-0.231

{0.00885-

0.00909}

1.21 {0.0476}

0.085-0.091

{0.00334-0.00358}

1.41 {0.0555}

0.218-0.224

{0.00858-

0.00881}

1.22 {0.0480}

0.078-0.084

{0.00307-0.00330}

1.42 {0.0559}

0.211-0.217

{0.00830-

0.00854}

1.23 {0.0484}

0.071-0.077

{0.00279-0.00303}

1.43 {0.0562}

0.204-0.210

{0.00803-

0.00826}

1.24 {0.0488}

0.064-0.070

{0.00251-0.00275}

1.44 {0.0566}

0.197-0.203

{0.00775-

0.00799}

1.25 {0.492}

0.057-0.063

{0.00224-0.00248}

1.45 {0.0570}

0.190-0.196

{0.00748-

0.00771}

1.26 {0.496}

0.050-0.056

{0.00196-0.00220}

1.46 {0.0574}

0.183-0.189

{0.00720-

0.00744}

1.27 {0.499}

0.043-0.049

{0.00169-0.00192}

1.47 {0.0578}

0.176-0.182

{0.00692-

0.00716}

1.28 {0.503}

0.036-0.042

{0.00141-0.00165}

1.48 {0.0582}

2007 Mazda MX-5 Miata Sport

2006-08 ENGINE Mechanical - Overhaul - 2.0L (LF) & 2.3L (L3) - Mazda6 & MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:43:26 PM

Page 88

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды