manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 693 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 693

1. Start the engine.  

2. Without depressing the clutch pedal, move the shift lever slowly to the reverse position until gear noise is 

heard and hold the lever in that position.  

3. Slowly depress the clutch pedal and hold at the point where the gear noise stops (clutch disengagement 

point).  

4. Measure distance A (from pedal not depressed to clutch disengagement point) and verify that it is within 

the specification. 

Clutch disengagement stroke (Reference value)

  

A: 80-110 mm {3.15-4.33 in}

  

Fig. 6: Inspecting Clutch Disengagement Point

 

Courtesy of MAZDA MOTORS CORP.

 

CLUTCH SWITCH INSPECTION 

1. Remove the engine cover.  

2. Remove the battery cover.  

 

2007 Mazda MX-5 Miata Sport 

2007 TRANSMISSION Clutch - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 1:44:45 PM

Page 9 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов