Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1383 | Manualshive

Страница: 1383 / 2244

background image

1. Follow "BEFORE SERVICE PRECAUTION" before performing any work operations to prevent fuel

from spilling from the fuel system. (See

BEFORE SERVICE PRECAUTION [LF]

.)

2. Remove the plug hole plate. (See

PLUG HOLE PLATE REMOVAL/INSTALLATION [LF]

.)

3. Remove the battery cover.

4. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

.)

5. Disconnect the fuel injector connector and move the harness slightly out of the way.

6. Remove in the order indicated in

Fig. 37

.

WARNING:



Fuel is very flammable liquid. If fuel spills or leaks from the
pressurized fuel system, it will cause serious injury or death and
facility breakage. Fuel can also irritate skin and eyes. To prevent
this, always complete the "

FUEL LINE SAFETY PROCEDURE

", while

referring to the BEFORE SERVICE PRECAUTION [LF] .

2007 Mazda MX-5 Miata Sport

2007 ENGINE Fuel System - MX-5 Miata

Microsoft

Thursday, July 09, 2009 2:37:12 PM

Page 42

© 2005 Mitchell Repair Information Company, LLC.

«
...
1381
1382
1383
1384
1385
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Camcar Страницы: 6

Бренд: UMBRA RIMORCHI Страницы: 18

Sterling ALL-TERRAIN 576

Бренд: Roadmaster Страницы: 12

Бренд: Parkeon Страницы: 43

Бренд: Icom Страницы: 20

Бренд: Buick Страницы: 20

Бренд: v.link Страницы: 21

Бренд: Gator Страницы: 6

Бренд: TEINHOF Страницы: 2

Бренд: Huf Страницы: 6

Бренд: BraunAbility Страницы: 46

CERTA CTCVINCVR14A

Бренд: Kogan Страницы: 4

Бренд: Toyota Страницы: 295

Бренд: Whispbar Страницы: 14

Бренд: CSL Страницы: 8

Бренд: Kuda Страницы: 3

Бренд: Prime Design Страницы: 12

Бренд: Front Runner Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды