Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1851 | Manualshive

Страница: 1851 / 2244

background image

2007 SUSPENSION

Rear Suspension - MX-5 Miata

REAR SUSPENSION LOCATION INDEX

Fig. 1: Identifying Location Of Rear Suspension Components

Courtesy of MAZDA MOTORS CORP.

REAR SHOCK ABSORBER AND COIL SPRING REMOVAL/INSTALLATION

1. When working on the left side, remove the fuel tank protector. (See

FUEL TANK

REMOVAL/INSTALLATION [LF]

.)

2. Remove in the order indicated in

Fig. 2

.

3. Install in the reverse order of removal.

CAUTION:



Performing the following procedures without first removing the ABS
wheel-speed sensor may possibly cause an open circuit in the wiring
harness if it is pulled by mistake. Before operations, remove the ABS
wheel-speed sensor (axle side), and move the sensor away from the
harnesses.

2007 Mazda MX-5 Miata Sport

2007 SUSPENSION Rear Suspension - MX-5 Miata

2007 Mazda MX-5 Miata Sport

2007 SUSPENSION Rear Suspension - MX-5 Miata

Microsoft

Thursday, July 09, 2009 1:52:15 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Thursday, July 09, 2009 1:52:29 PM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

«
...
1849
1850
1851
1852
1853
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Metra Electronics Страницы: 14

Бренд: ULTIMATE SPEED Страницы: 19

Бренд: Harken Hoister Страницы: 12

Бренд: Yamaha Страницы: 2

Бренд: Porsche Страницы: 144

CARPOWER CAP-12XHQ

Бренд: Monacor Страницы: 5

Grand Cherokee WK2

Бренд: Jeep Страницы: 338

Бренд: AMP Research Страницы: 12

Half Size Trunk Box Organizer C-TBO-CV

Бренд: Havis-Shields Страницы: 1

Бренд: Volvo Страницы: 8

Indigo MANZA QUADRAJET 90

Бренд: TATA Motors Страницы: 10

Бренд: STC Страницы: 6

Бренд: Honda Страницы: 85

2014 Grand Cherokee SRT8

Бренд: Jeep Страницы: 596

Бренд: Skoda Страницы: 4

Бренд: iOttie Страницы: 58

Бренд: Vauxhall Страницы: 131

Бренд: Ford Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды