Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 789

Страница: 789 / 2244

Fig. 43: Measuring Width Of Differential Gear Case Component In Differential Carrier

Courtesy of MAZDA MOTORS CORP.

1. The combined thickness of the left and right adjustment shims is obtained by the following formula.

Shim thickness (mm {in}) =B-A+ (0.01-0.03 {0.0004-0.0118 in})

2. If the combined thickness of the previously assembled adjustment shims is equal to the calculated

thickness, use the shims as they are.

3. If the combined thickness of the previously assembled adjustment shims is not equal to the calculated

thickness, or if the adjustment shims have to be replaced, select two appropriate adjustment shims from
the table below.

ADJUSTMENT SHIM TABLE

Identification mark

Thickness (mm {in})

Identification mark

Thickness (mm {in})

550

5.50 {0.217}

605

6.05 {0.238}

560

5.60 {0.220}

610

6.10 {0.240}

565

5.65 {0.222}

615

6.15 {0.242}

570

5.70 {0.224}

620

6.20 {0.244}

575

5.75 {0.226}

625

6.25 {0.246}

580

5.80 {0.228}

630

6.30 {0.248}

585

5.85 {0.230}

635

6.35 {0.250}

2007 Mazda MX-5 Miata Sport

2007 DRIVELINE/AXLES Differential - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:11:17 PM

Page 45

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды