manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1595 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1595

3. Pull the shock absorbing pad rearward and detach clips A.  

4. Remove the shock-absorbing pad.  

5. Install in the reverse order of removal. 

Fig. 56: Identifying Shock-Absorbing Pad

 

Courtesy of MAZDA MOTORS CORP.

 

HEADLINER REMOVAL/INSTALLATION [DETACHABLE HARDTOP] 

1. Remove the detachable hardtop.  

2. Remove the following parts: 

1. B-pillar garnish.  

2. Side lock.  

3. B-pillar upper trim. (See 

B-PILLAR UPPER TRIM REMOVAL [DETACHABLE 

HARDTOP]

 .)  

4. Male wedge cover.  

5. Top lock cover.  

3. Remove the fasteners.  

4. Pull the headliner outward and remove it.  

5. Install in the reverse order of removal. 

 

2007 Mazda MX-5 Miata Sport 

2007 ACCESSORIES & BODY, CAB Interior Trim - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 3:29:26 PM

Page 54 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов