manualshive.com logo in svg

Mazda MX-5 Miata Sport 2007, Руководство пользователя, Страница: 1951 / 2244

Поделиться
Скачать
Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1951

terminal A and 
instrument cluster 
terminal 3AA  

Between coil 
terminal B and 
instrument cluster 
terminal 3Y  

 
Is there any malfunction?

8

Inspect the following 
wiring harnesses and 
connectors for an open or 
short circuit: 

Between keyless 
control module 
terminal 4A and 
instrument cluster 
terminal 2Q  

Between keyless 
control module 
terminal 4C and 
instrument cluster 
terminal 2S  

Is there any malfunction?

Yes

Repair or replace wiring 
harness and connectors.

No

Go to the next step.

9

Is there continuity 
between PCM terminal 
1B and starter relay with 
clutch pedal depressed 
(MT with starter 
interlock system), P or N 
position (AT)?

Yes

Go to the next step.

No

Repair or replace wiring 
harness.

10

Is clicking sound heard 
from starter when the 
ignition switch is turned 
to START?

Yes

Go to the next step.

No

Go to Step 13.

11

Inspect the starting 
system. 
(See 

STARTER 

INSPECTION [LF]

 .) 

Is starting system 
normal?

Yes

Inspect for 
seized/hydrolocked 
engine, flywheel or drive 
plate. 
(See 

FLYWHEEL 

INSPECTION

 .)

No

Repair or replace 
components if required.

 

2007 Mazda MX-5 Miata Sport 

2007 ENGINE PERFORMANCE Symptom Troubleshooting - MX-5 Miata

  

Microsoft 

 

Thursday, July 09, 2009 2:42:09 PM

Page 18 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов