Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 1190 | Manualshive

Страница: 1190 / 2244

background image

Fig. 34: AM/FM Antenna Feeder No. 2 Continuity Table
Courtesy of MAZDA MOTORS CORP.

Fig. 35: Identifying AM/FM Antenna Feeder No. 2 Terminals & Connectors

Courtesy of MAZDA MOTORS CORP.

AUDIO CONTROL SWITCH REMOVAL/INSTALLATION

1. Remove the battery cover.

2. Disconnect the negative battery cable. (See

BATTERY REMOVAL/INSTALLATION [LF]

.)

3. Remove the driver-side air bag module. (See

DRIVER-SIDE AIR BAG MODULE

REMOVAL/INSTALLATION

.)

4. Remove the steering wheel. (See

STEERING WHEEL AND COLUMN

REMOVAL/INSTALLATION

.)

5. Remove in the order indicated in

Fig. 36

.

NOTE:



For vehicles with the cruise control system, the audio control switch
harness and the cruise control switch harness are united, therefore they
cannot be separated.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Entertainment - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:34:33 PM

Page 32

© 2005 Mitchell Repair Information Company, LLC.

«
...
1188
1189
1190
1191
1192
...
»

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MX-5 Miata Sport 2007

Бренд: Abarth Страницы: 176

ESCALADE - BROCHURE 2009

Бренд: Cadillac Страницы: 24

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Green Motion Building

Бренд: Eaton Страницы: 12

10-8002-C11670C

Бренд: Saleen Страницы: 17

Бренд: Rago FABRICATION Страницы: 10

Бренд: Whispbar Страницы: 14

Бренд: Metra Electronics Страницы: 8

Бренд: Yakima Страницы: 11

Бренд: Honda Страницы: 20

2009 Rio Series

Бренд: Kia Страницы: 219

Бренд: Subaru Страницы: 298

Бренд: DriveRight Страницы: 16

Бренд: Air Lift Страницы: 28

Бренд: Dolphin Страницы: 16

Бренд: Prorack Страницы: 15

Grand Cherokee SRT 2019

Бренд: Jeep Страницы: 656

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды