Mazda MX-5 Miata Sport 2007 Скачать руководство пользователя страница 202

Страница: 202 / 2244



When using the IDS (laptop PC)

1. Select "BODY"

2. Select "SECURITY"

3. Select "PATS functions"



When using the PDS (Pocket PC)

1. Select "Programming".

2. Select "PATS functions"

5. Then, select items from the screen menu in the following order.

1. Select "Program Additional Card Key".

6. Security access begins and the M-MDS displays the "OUT-CODE".

7. Input the "IN-CODE" that corresponds to the "OUT-CODE "displayed on the M-MDS screen.

8. Select "CARD KEY PROGRAMMING" from the M-MDS screen menu.

9. Press the unprogrammed card key UNLOCK button

twice.

10. If programming more card keys, remove the supplementary key once, and then repeat the procedure from

Step 7 by following the instructions on the M-MDS screen.

CLEARING CARD KEY[ADVANCED KEYLESS SYSTEM]

1. Fully lower the driver-side door glass.

2. Connect the M-MDS to the DLC-2.

3. Pull out the M-MDS cable from the door glass opening and set the M-MDS outside the vehicle.

NOTE:



When "OUT-CODE" is first displayed, turning the ignition switch from
the LOCK to the ON position 5 times will change the "OUT-CODE".

NOTE:



After Step 8 is completed and the card key programming is activated,
the door lock actuator operates to lock, and then operates to unlock.

NOTE:



After Step 9 is completed and the card key is programmed, the door
lock actuator operates to lock, and then operates to unlock.

CAUTION:



Protect the cable and body contact area with a clean rag,
otherwise they could be damaged.

2007 Mazda MX-5 Miata Sport

2007 ACCESSORIES & BODY, CAB Security and Locks (Advanced Keyless System) - MX-5 Miata

Microsoft

Thursday, July 09, 2009 3:36:54 PM

Page 43

Содержание MX-5 Miata Sport 2007





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды

Mazda MX-5 Miata Sport 2007, Руководство пользователя

Результаты поиска

Содержание MX-5 Miata Sport 2007

Отзывы:

Похожие инструкции для MX-5 Miata Sport 2007

Бренды по названию

Популярные бренды